Step 1: Mounting the device on a wall or table:
Start of by unpacking the device and mounting it to the location of your choice. Locate the table stand and the mounting rail in the box and decide where you want to put the Asema E in your home. Depending on your choice, you have the option of wall mount or table stand. Follow the instructions on the box on how to assemble the components. For table installation, assemble the table stand (note: to attach the mounting rail to the bottom of the table stand, you need to slide it in from the bottom). For wall installation, attach the mounting rail to a wall with two screws. Then slide the Asema E to the mounting rail.

Step 2:
Locate the USB power adapter in the box. Unwrap the white power cable and attach the USB-A (large) connector to the adapter. Then insert the smaller micro-USB end of the cable to the micro-USB socket on Asema E. Note that there are two micro-USB sockets on an Asema E; one for power and one for reprogramming the device (so called "firmware flashing"). Please use the correct connector that is marked with "POWER" and indicated with green in the image below.
Now connect the USB power adapter to a power supply wall socket. Do not touch the Asema E screen while connecting it to a power. Finger tap on the screen during startup will instruct the device to go to factory mode and it will not start up. If you did have your fingers on screen, simply unplug the power connector and try again.
The device will now start up. If this is the first time the device is powered up, startup might take a few minutes as the software is initialized. Once done the device will take you to the Startup Wizard.

Asema S1 controlling a roof lamp
1. Switch off mains power of the circuit under installation
2. Connect incoming neutral and phase
3. Connect the lamp to outgoing neutral and phase as indicated by symbols on Asema S1
4. Optionally attach the controller to the roof with screws

Asema S1 inside a light switch
1. Switch off mains power of the circuit under installation
2. Uncover the switch controller screws on Asema S1, and if needed cut the wire connector protective plastic
3. Connect incoming and outgoing leads
4. Connect the light switch to the switch connector
5. Insert controller to wall and close

Asema S1 behind a Schuko wall socket
1. Switch off mains power of the circuit under installation
2. If installation space is limited, cut the protective plastic from the wire connector of the controller
3. Place the controller next to the socket and connect outgoing neutral and phase
4. Connect incoming neutral and phase as indicated by symbols on Asema S1
5. Insert controller and socket to wall and close

To install Asema S2 inside an electrical panel

1. Switch off mains power of the panel
2. Locate the fuse (max 16 A) protecting the targeted appliance or group
3. Connect Asema S2 to the load in series after the fuse by attaching incoming and outgoing neutral and phase.

To install Asema S3 as floor swicth
1. Unplug the power cord of the appliance to control.
2. Connect the appliance to Asema S3 controller.
3. Place Asema S3 on the floor and connect it to the wall socket.

To mount Asema S3 to a wall socket

1. To mount the S3, attach the wall mount into the base of the Asema S3
2. Wrap to power cables into the holders of the wall mount
3. Push the male power cable head into the slot in the middle of the wall mount.
4. Plug the controller to the socket and connect the appliance

Step 1: Attaching the Asema A1 to the Power Meter
Asema A1 is attached to one of the relay slots in the power meter as shown in the figure above. Ensure that the radio module connector (green) is properly attached and then slide in the module as far as it goes.

Step 2: Connecting the data cable
After attaching the radio module, insert its data cable to the connector on the right side of the power meter as shown in the image below. Once the data cable is connected, the radio module is ready to operate.

Installing Asema M1 to your home

1. Attach the unit to the wall the way you wish.
2. Locate the LED light of the power meter.
3. Detach one half of the velcro sticker on the Asema M1 LED head.
4. Attach the sticker to the LED light so that the LED is clearly visible through the hole of the sticker.
5. Place the Asema M1 LED head on the sticker.
6. Asema M1 comes with a standard 10A Schuko mains cable. Plug this into a wall socket to connect power to the unit.

Installing the Asema M2 meter

1. Locate the three incoming phases in the fuse box that go to the main fuse/power switch.
2. Attach the current clamps onto the leads as indicated by the installation diagram on the device. The clamps are attached to the leads only, do not attach them to the neutral.
3. Note the numbering on the clamps, they should match the numbering of the phases to correctly display the power consumption of that phase. Please notice that you don't have to cut any of the phases in order to get the Asema M2 working properly. The clamps measure your power consumption through the protective shielding of the phase.

The Asema M2 is powered by 230V power from one of the phases. You may freely choose the phase. Do not take power from the incoming phases, always draw the power from a lead located behind the main switch.